A rod-shaped explosively formed penetrator warhead
-
摘要: 为进一步提高周向多爆炸成型侵彻体战斗部的毁伤效能，设计了一种爆炸成型杆式侵彻体战斗部。结合数值模拟方法，对侵彻体的成型过程及飞散效果进行模拟，分析了外衬对侵彻体成型质量的影响，并设计出侵彻体结构密实的杆式MEFP战斗部。制备了有外衬和无外衬两种战斗部原理样机并进行静爆实验。实验结果表明，无外衬战斗部成型侵彻体对3 m处40 mm厚45钢板平均穿深为27 mm，有外衬战斗部成型侵彻体可贯穿3 m处40 mm厚45钢板；侵彻体对靶板的侵彻实验结果与模拟结果一致。通过设计外衬结构，战斗部成型侵彻体的成型质量和侵彻威力都大幅度提高。Abstract: In order to further improve the damage capacity of the multiple explosively formed penetrator (MEFP) warhead, we designed a rod-shaped and explosively formed penetrator warhead. We firstly investigated the formation process and scattering effect of the penetrator were investigated using numerical simulation, and presented a design of rod-shaped warhead penetrators based on the analysis of the influence of the warhead's outer linings on the penetrator's formation process. Then we fabricated two principal prototypes of the penetrator warhead, one with and the other without outer linings, and performed the static explosion experiments to find out about their damage effects. The results show that the average penetration depth on the 40 mm-thick-45 steel, 3 m apart from the detonation center by the warhead penetrators without outer linings, is 27 mm., while those with outer linings can completely penetrate the target. Moreover, the penetration results of the experiment and the simulation are consistent with each other, thereby concluding that our design can significantly improve the formation quality and the penetration power of the rod-shaped penetrators.
-
Key words:
- liner /
- velocity gradient /
- rod-shaped penetrator /
- numerical simulation /
- static explosion experiment
-
图 2 无外衬战斗部模型及杆式侵彻体整体飞散效果
Figure 2. Model of warhead without outer linings and scattering effect of penetrators
图 3 单枚药型罩速度随时间变化及速度梯度
Figure 3. Velocity variation by time (a) and velocity gradient of single liner (b)
图 5 冲击波由低阻抗介质传入高阻抗介质
Figure 5. Shock wave transmitting from low impedance medium to high impedance medium
图 6 有外衬战斗部模型及杆式侵彻体整体飞散效果
Figure 6. Model of warhead with outer linings and scattering effect of penetrators
图 7 单枚药型罩速度随时间变化及速度梯度
Figure 7. Variation of velocity with time (a) and velocity gradient of single liner (b)
图 13 杆式侵彻体毁伤实验效果
Figure 13. Rod-shaped penetrator's damage effect produced in experiment
图 14 杆式侵彻体毁伤模拟效果
Figure 14. Rod-haped penetrator's damage effect produced in simulation
表 1 材料状态方程参数
Table 1. Material parameters of equation of state
材料 ρ/(g·cm3) C/(km·s-1) S γ Material ρ/(g·cm3) C/(km·s-1) S γ 纯铁 7.86 4.61 1.730 2.0 紫铜 8.96 3.94 1.489 2.02 
下载: 导出CSV
表 2 材料本构模型参数
Table 2. Material parameters of constitutive model
材料 G/GPa A/MPa B/MPa n c m Tm/K Tr/K 纯铁 64 469 802 0.401 0.019 0.432 1 832 293 紫铜 80 500 320 0.280 0.064 1.060 1 790 293
下载: 导出CSV
-
[1] 相升海, 徐文龙, 张建, 等.刻槽式MEFP的成型及侵彻钢靶模式[J].爆炸与冲击, 2015, 35(1):135-139. doi: 10.11883/1001-1455(2015)01-0135-05XIANG Shenghai, XU Wenlong, ZHANG Jian, et al. Groove type MEFP formation and penetrating steel target's pattern[J]. Explosive and Shock Waves, 2015, 35(1):135-139. doi: 10.11883/1001-1455(2015)01-0135-05 [2] CARDOSO D, TEIXEIRA-DIAS F. Modelling the formation of explosively formed projectiles (EFP)[J]. International Journal of Impact Engineering, 2016, 93:116-127. doi: 10.1016/j.ijimpeng.2016.02.014 [3] 吴峰, 孔毓琦, 柳科学, 等.周向MEFP式战斗部结构设计与仿真[J].机械制造与自动化, 2013, 42(3):110-114. http://www.cnki.com.cn/Article/CJFDTotal-ZZHD201303039.htmWU Feng, KONG Yuqi, LIU Kexue, et al. Structural design and simulation of circumferential warhead with MEFP[J]. Machine Building and Automation, 2013, 42(3):110-114. http://www.cnki.com.cn/Article/CJFDTotal-ZZHD201303039.htm [4] 梁振刚, 蒋建伟.周向MEFP成型规律数值分析[J].弹箭与制导学报, 2015, 35(2):57-60. http://www.wanfangdata.com.cn/details/detail.do?_type=perio&id=djyzdxb201502015LIANG Zhengang, JIANG Jianwei. A numerical analysis on the forming law of circumferential MEFP[J]. Journal of Projectiles, Rockets, Missiles and Guidance, 2015, 35(2):57-60. http://www.wanfangdata.com.cn/details/detail.do?_type=perio&id=djyzdxb201502015 [5] 尹建平, 王志军, 熊永家, 等.药型罩曲率半径对周向MLEFP成型的影响[J].含能材料, 2013, 21(4):512-516. http://wuxizazhi.cnki.net/Sub/wqjs/a/HNCL201304012.htmlYIN Jianping, WANG Zhijun, XIONG Yongjia, et al. Influence of liner curvature on formation of circumferential multiple linear explosively formed penetrators[J]. Chinese Journal of Energetic Material, 2013, 21(4):512-516. http://wuxizazhi.cnki.net/Sub/wqjs/a/HNCL201304012.html [6] 时党勇, 张庆明, 翟喆, 等.形成尾翼爆炸成型弹丸的贴片方法[J].火工品, 2009(6):46-49. http://www.wanfangdata.com.cn/details/detail.do?_type=perio&id=hgp200906014SHI Dangyong, ZHANG Qingming, ZHAI Zhe, et al. Foil method of producing explosively formed projectile with star-shaped tail[J]. Initators and Pyrotechnics, 2009(6):46-49. http://www.wanfangdata.com.cn/details/detail.do?_type=perio&id=hgp200906014 [7] 朱传胜. 带隔板爆炸成型弹丸战斗部成型技术研究[D]. 南京: 南京理工大学, 2014. http://www.wanfangdata.com.cn/details/detail.do?_type=degree&id=Y2976517 [8] 苟瑞君. 线性爆炸成型侵彻体形成机理研究[D]. 南京: 南京理工大学, 2006. http://www.wanfangdata.com.cn/details/detail.do?_type=degree&id=Y1154993 [9] MEYERS M A. 材料的动力学行为[M]. 张庆明, 刘彦, 黄风雷, 等译. 北京: 国防工业出版社, 2006: 134-137. -
计量
- 文章访问数: 5354
- HTML全文浏览量: 1316
- PDF下载量: 262
- 被引次数: 0