弧形折纸模式薄壁结构的压缩变形与能量吸收

张天辉; 邓健强; 刘志芳; 李世强

doi:10.11883/bzycj-2019-0355

弧形折纸模式薄壁结构的压缩变形与能量吸收

doi: 10.11883/bzycj-2019-0355

太原理工大学机械与运载工程学院应用力学研究所, 山西太原 030024

基金项目: 国家自然科学基金（11602161，11772216）

详细信息

作者简介:
张天辉（1992－　），男，硕士，zhangtianhui1234@163.com

通讯作者:
李世强（1986－　），男，博士，副教授，lishiqiang@tyut.edu.cn

中图分类号: O347.1
计量
- 文章访问数: 4828
- HTML全文浏览量: 1984
- PDF下载量: 110
- 被引次数: 0
出版历程
- 收稿日期: 2019-09-15
- 修回日期: 2019-12-19
- 网络出版日期: 2020-06-25
- 刊出日期: 2020-07-01

Compression deformation and energy absorption of thin-walled structures with arc-shaped origami patterns

Institute of Applied Mechanics, College of Mechanical and Vehicle Engineering, Taiyuan University of Technology, Taiyuan 030024, Shanxi, China

摘要

摘要: 选用PolyMax^TM PLA为试样材料，利用3D打印技术制备了弧形折纸薄壁管件。基于准静态轴向压缩实验，运用ABAQUS软件对弧形折纸薄壁管件轴向准静态压缩和冲击行为进行了有限元计算，探讨了其变形模式和能量吸收特性，分析了预折角和薄壁单胞管件阵列数量对其压溃模式及能量吸收的影响。有限元计算结果与实验结果吻合较好。薄壁管件的变形过程可分为4个阶段：初始压溃阶段、预折角塑性旋转阶段、腹板塑性屈曲阶段和完全压溃密实化阶段。弧形折痕的引入能够有效地降低薄壁管件在压缩过程中的初始压溃载荷峰值，减小冲击载荷的振荡幅值。对比了高度相等、质量近似相等的方管与弧形折纸薄壁管在不同冲击速度下的压缩变形与能量吸收。在准静态压缩作用下，对于单胞模型，仅有折痕倾角为70°的模型的比吸能优于方管；对于多胞管件阵列模型，方管的比吸能均优于折纸管。折纸管的压缩力效率和比总体效率均优于方管，其中折痕倾角为50°的模型的压缩力效率和比总体效率最高。在动态冲击压缩下，阵列方管的比吸能均优于阵列折纸管。当冲击速度为10 m/s时，折纸管的压缩力效率和比总体效率均优于方管，其中折痕倾角为50°的模型的压缩力效率和比总体效率最高。当冲击速度为20 m/s时，仅有折痕倾角为50°的模型的压缩力效率和比总体效率优于方管。
- 薄壁管状结构 /
- 弧形折纸 /
- 冲击载荷 /
- 压缩吸能 /
- 折痕倾角
Abstract: By chosing PolyMax^TM PLA as the sample material, thin-walled tube structures with arc-shaped origami patterns were prepared by a three-dimensional printing technology. Based on quasi-static axial compression experiments, their axial quasi-static crushing and impact compression deformation modes and energy absorption were simulated by using the ABAQUS software to investigate the influences of the prefolding angle and the number of in-plane arrays on the crushing mode and energy absorption of the structures. The results by the finite element calculation are in agreement with the experimental ones. The deformation of the tubes can be divided into four stages including initial crushing stage, prefolding-angle plastic rotation stage, web plastic buckling stage, and complete crushing and densification stage. The arc-shaped corrugations demonstrate some obvious advantages at reducing the initial peak force and the fluctuation range of the impact force. The square tube was compared with the arc-shaped origami patterns with the same height and approximately the same mass. For the single-cell models, the specific energy absorption of the model with only 70° crease inclination is higher than that of the square tube under the quasi-static crushing. For the multiple-array tube structures, the specific energy absorption of the single-cell square tube is higher than those of the arc-shaped tubes. When considering the crush force efficiency and specific total efficiency, the arc-shaped tubes have an advantage over the square tubes, the model with a crease inclination of 50° is the best. Under the impact crushing loading condition, the specific energy absorptions of the multiple-array tubes are higher than those of the arc-shaped tubes. The crush force efficiency and specific total efficiency of the arc-shaped tubes are higher than those of the square tubes under the impact velocity of 10 m/s, the model with a crease inclination of 50° is the highest. The crush force efficiency and specific total efficiency of the model with only 50° crease inclination are higher than those of the square tube under the impact velocity of 20 m/s.
- thin-walled tube structure /
- arc-shaped origami /
- impact loading /
- compressive energy absorption /
- crease inclination

HTML全文

图 1 弧形折痕薄壁管建模过程

Figure 1. The modeling process of an origami thin-walled tube with the arc-shape pattern

下载: 全尺寸图片幻灯片

图 2 利用PolyMax^TM PLA 打印的哑铃形试件的拉伸真实应力应变关系及打印工艺

Figure 2. True stress-strain relation of a dumbbell-shaped sample printed with PolyMax^TM PLA and the corresponding printing process

下载: 全尺寸图片幻灯片

图 3 模拟与实验压缩载荷-位移曲线对比

Figure 3. Comparison of compressive load-displacement curves between simulation and experimentl

下载: 全尺寸图片幻灯片

图 4 弧形折痕薄壁管状结构单胞有限元模型

Figure 4. The finite element model of a curved origami thin-walled tube

下载: 全尺寸图片幻灯片

图 5 网格敏感性验证

Figure 5. Validation of mesh sensitivity

下载: 全尺寸图片幻灯片

图 6 有限元算法验证

Figure 6. Verification of the finite element algorithm

下载: 全尺寸图片幻灯片

图 7 不同单胞模型的应力-应变曲线

Figure 7. Stress-strain curves of different single-cell models

下载: 全尺寸图片幻灯片

图 8 面内方向阵列个数为2×2的阵列模型的应力-应变曲线

Figure 8. Stress-strain curves corresponding to the models with the number n of in-plane arrays equal to 2×2

下载: 全尺寸图片幻灯片

图 9 面内方向阵列个数不同的A60°模型的应力-应变曲线

Figure 9. Stress-strain curves of different in-plane arrays number of A60° models

下载: 全尺寸图片幻灯片

图 10 不同冲击速度下，不同阵列模型的应力-应变曲线

Figure 10. Stress-strain curves of different models under different impact velocities

下载: 全尺寸图片幻灯片

图 11 准静态压缩下不同的单胞薄壁管比吸能随位移的变化

Figure 11. Specific energy absorption varying with displacement for different single-cell thin-walled tubes under quasi-static compression

下载: 全尺寸图片幻灯片

图 12 不同冲击速度下面内方向阵列个数相同的不同薄壁管结构比吸能的对比

Figure 12. Comparison of specific energy absorption for different thin-walled tubes with the same number of in-plane arrays under different impact velocities

下载: 全尺寸图片幻灯片

图 13 不同薄壁管模型压缩力效率的对比

Figure 13. Comparison of crush force efficiencies for different thin-walled tube models

下载: 全尺寸图片幻灯片

图 14 压缩力效率随压缩位移的变化

Figure 14. Crush force efficiency varying with compressive displacement

下载: 全尺寸图片幻灯片

图 15 不同薄壁管模型比总体效率的对比

Figure 15. Comparison of specific total efficiencies for different thin-walled tube models

下载: 全尺寸图片幻灯片

图 16 比总体效率随压缩位移的变化

Figure 16. Specific total efficiency varying with compressive displacement

下载: 全尺寸图片幻灯片

表 1 模型参数

Table 1. The parameters of the models

模型	单胞质量/g	h/mm	w/mm	l/mm	τ/mm	c/mm	a/mm	h₀/mm	ξ /(°)	α/(°)	θ/(°)	β/(°)
A50°	8.65	30	40	45.23	1.10	10	14.26	10.92	60	50	42	61
A60°	8.66	30	40	41.57	1.20	10	11.98	10.37	60	60	55	71
A70°	8.59	30	40	38.86	1.25	10	10.79	10.14	60	70	67	78
SQU	8.66	30	40	41.89	1.47

下载: 导出CSV

表 2 不同模型的初始压溃载荷峰值

Table 2. Initial peak crushing loads of different models

冲击速度/(m·s⁻¹)	n	载荷/kN
冲击速度/(m·s⁻¹)	n	A50°	A60°	A70°	SQU
1	1×1	0.23	0.65	1.72	6.59
1	2×2	1.72	3.91	8.47	32.46
10	2×2	4.92	9.06	13.22	42.84
20	2×2	10.47	19.77	23.72	46.14

下载: 导出CSV

参考文献(15)

[1]	LEE T U, YOU Z, GATTAS J M. Elastica surface generation of curved-crease origami [J]. International Journal of Solids and Structures, 2018, 136-137: 13–27. DOI: 10.1016/j.ijsolstr.2017.11.029.
[2]	SINGACE A A, EL-SOBKY H. Behaviour of axially crushed corrugated tubes [J]. International Journal of Mechanical Sciences, 1997, 39(3): 249–268. DOI: 10.1016/S0020-7403(96)00022-7.
[3]	ZHANG X, CHENG G D, YOU Z, et al. Energy absorption of axially compressed thin-walled square tubes with patterns [J]. Thin-Walled Structures, 2007, 45(9): 737–746. DOI: 10.1016/j.tws.2007.06.004.
[4]	ZHAO Z A, KUANG X, WU J T, et al. 3D printing of complex origami assemblages for reconfigurable structures [J]. Soft Matter, 2018, 14(39): 8051–8059. DOI: 10.1039/C8SM01341A.
[5]	MA J Y, YOU Z. Energy absorption of thin-walled square tubes with a prefolded origami pattern: Part I: geometry and numerical simulation [J]. Journal of Applied Mechanics, 2014, 81(1): 011003. DOI: 10.1115/1.4024405.
[6]	SONG J, CHEN Y, LU G X. Axial crushing of thin-walled structures with origami patterns [J]. Thin-Walled Structures, 2012, 54: 65–71. DOI: 10.1016/j.tws.2012.02.007.
[7]	ZHOU C H, ZHOU Y, WANG B. Crashworthiness design for trapezoid origami crash boxes [J]. Thin-Walled Structures, 2017, 117: 257–267. DOI: 10.1016/j.tws.2017.03.022.
[8]	周昳鸣, 周才华, 王博. 预折纹吸能管的多样性可竞争优化设计 [J]. 振动与冲击, 2016, 35(19): 143–147. DOI: 10.13465/j.cnki.jvs.2016.19.024. ZHOU Y M, ZHOU C H, WANG B. Optimization design for pre-fold energy absorption tubes [J]. Journal of Vibration and Shock, 2016, 35(19): 143–147. DOI: 10.13465/j.cnki.jvs.2016.19.024.
[9]	郝文乾, 卢进帅, 黄睿, 等. 轴向冲击载荷下薄壁折纹管的屈曲模态与吸能 [J]. 爆炸与冲击, 2015, 35(3): 380–385. DOI: 10.11883/1001-1455-(2015)03-0380-06. HAO W Q, LU J S, HUANG R, et al. Buckling and energy absorption properties of thin-walled corrugated tubes under axial impacting [J]. Explosion and Shock Waves, 2015, 35(3): 380–385. DOI: 10.11883/1001-1455-(2015)03-0380-06.
[10]	HOU D G, CHEN Y, MA J Y, et al. Axial crushing of thin-walled tubes with kite-shape pattern [C] // Proceedings of ASME 2015 International Design Engineering Technical Conferences and Computers and Information in Engineering Conference. Boston, Massachusetts, USA: American Society of Mechanical Engineers, 2015: 5. DOI: 10.1115/DETC2015-46671.
[11]	MA J Y, HOU D G, CHEN Y, et al. Quasi-static axial crushing of thin-walled tubes with a kite-shape rigid origami pattern: numerical simulation [J]. Thin-Walled Structures, 2016, 100: 38–47. DOI: 10.1016/j.tws.2015.11.023.
[12]	LI S Q, LI X, WANG Z H, et al. Sandwich panels with layered graded aluminum honeycomb cores under blast loading [J]. Composite Structures, 2017, 173: 242–254. DOI: 10.1016/j.compstruct.2017.04.037.
[13]	LI S Q, LI X, WANG Z H, et al. Finite element analysis of sandwich panels with stepwise graded aluminum honeycomb cores under blast loading [J]. Composites Part A: Applied Science and Manufacturing, 2016, 80: 1–12. DOI: 10.1016/j.compositesa.2015.09.025.
[14]	QIAO J X, CHEN C Q. In-plane crushing of a hierarchical honeycomb [J]. International Journal of Solids and Structures, 2016, 85−86: 57–66. DOI: 10.1016/j.ijsolstr.2016.02.003.
[15]	SANTOSA S P, WIERZBICKI T, HANSSEN A G, et al. Experimental and numerical studies of foam-filled sections [J]. International Journal of Impact Engineering, 2000, 24(5): 509–534. DOI: 10.1016/S0734-743X(99)00036-6.