Energy absorption characteristics of axial series energy absorption tubes

ZHANG Xiao; XIAO Yong; LIU Hongbo; LIU Qi; DU Xiaokun; ZHANG Yangyang

doi:10.11883/bzycj-2023-0460

Volume 44 Issue 11

Nov. 2024

Turn off MathJax

Article Contents

Abstract

References

Article Navigation > Explosion And Shock Waves > 2024 > 44(11): 113103

WANG De-tian, LI Ze-ren, WU Jian-rong, LIU Shou-xian, LIU Jun, MENG Jian-hua, PENG Qi-xian, CHEN Guang-hua, LIU Qiao. An optical-fiber displacement interferometer for measuring velocities of explosively-driven metal plates[J]. Explosion And Shock Waves, 2009, 29(1): 105-108. doi: 10.11883/1001-1455(2009)01-0105-04

Citation:

ZHANG Xiao, XIAO Yong, LIU Hongbo, LIU Qi, DU Xiaokun, ZHANG Yangyang. Energy absorption characteristics of axial series energy absorption tubes[J]. Explosion And Shock Waves, 2024, 44(11): 113103. doi: 10.11883/bzycj-2023-0460

Citation:

PDF( 2858 KB)

Energy absorption characteristics of axial series energy absorption tubes

doi: 10.11883/bzycj-2023-0460

Beijing Institute of Space Launch Technology, Beijing 100076, China

Received Date: 2023-12-24
Rev Recd Date: 2024-04-02

Available Online: 2024-05-08

Publish Date: 2024-11-15

Abstract

Abstract

To address the issue of peak load reduction for impact loads in engineering technology, the energy absorption characteristics of axial series energy absorbing tubes was investigated through a combination of numerical simulation and experimentation. Firstly, the Johnson-Cook dynamic constitutive parameters of the material 06Cr18Ni11Ti GB/T1220-2007 of energy absorbing tubes were established and evaluated based on high-speed tensile tests which indicates 06Cr18Ni11Ti has obvious strain rate hardening effect. Subsequently, numerical simulation and high-speed impact tests were conducted to examine the energy absorption characteristics of energy absorption tubes, with an evaluation of consistency between numerical simulation and test results. The numerical simulation was based on the time-step ABAQUS/Explicit finite element simulation platform. The high speed impact test system used the high pressure gas inside the air actuated piston cylinder as the power source, which could accelerate the mass block to a speed of 30 m/s. Finally, the energy absorption evaluation indexes between the axial series configuration and the single configuration of the energy absorption tube were compared and analyzed by numerical simulation. The analysis demonstrates that deformation mode, load curve, and energy absorption evaluation indexes from both numerical simulations and impact tests exhibit good agreement. The accuracy of material performance parameters confirms the effectiveness of simulation prediction methods while validating reasonability and reliability of high-speed impact test schemes. Compared to axial series configurations with identical structural parameters, single-tube configurations display asymmetric and unstable twist deformations during compression processes. Single-tube configurations experience a 13% reduction in effective compression stroke along with a 33.4% increase in peak load, 15% increase in instantaneous impact load, 13% increase in average compression force, as well as a 17.7% increase in peak-to-average load ratio. Consequently, axial series configurations prove to be more ideal energy absorbing structures.
- axial series,
- energy absorption tube,
- dynamic constitutive,
- finite element analysis,
- high-speed impact test

FullText(HTML)

References(18)

References

[1]	ALEXANDER J M. An approximate analysis of the collapse of thin cylindrical shells under axial loading [J]. The Quarterly Journal of Mechanics and Applied Mathematics, 1960, 13(1): 10–15. DOI: 10.1093/qjmam/13.1.10.
[2]	PUGSLEY A. The large-scale crumpling of thin cylindrical columns [J]. The Quarterly Journal of Mechanics and Applied Mathematics, 1960, 13(1): 1–9. DOI: 10.1093/qjmam/13.1.1.
[3]	WIERZBICKI T, BHAT S U. A moving hinge solution for axisymmetric crushing of tubes [J]. International Journal of Mechanical Sciences, 1986, 28(3): 135–151. DOI: 10.1016/0020-7403(86)90033-0.
[4]	张雄. 轻质薄壁结构耐撞性分析与设计优化 [D]. 大连: 大连理工大学, 2008: 3–13. ZHANG X. Crashworthiness analysis and design optimization of light thin-walled structures [D]. Dalian: Dalian University of Technology, 2008: 3–13.
[5]	毕世华, 王汉平, 梁征. 导弹垂直弹射过程中制动锥的动力学特性研究 [J]. 北京理工大学学报, 2004, 24(9): 762–765. DOI: 10.3969/j.issn.1001-0645.2004.09.003. BI S H, WANG H P, LIANG Z. A study on the dynamical characteristics of the braking cylindrical shells during the vertical ejection of missiles [J]. Transactions of Beijing Institute of Technology, 2004, 24(9): 762–765. DOI: 10.3969/j.issn.1001-0645.2004.09.003.
[6]	王汉平, 王忠峰. 导弹弹射系统中缓冲制动锥的轴压特性 [J]. 北京理工大学学报, 2007, 27(2): 99–102. DOI: 10.3969/j.issn.1001-0645.2007.02.002. WANG H P, WANG Z F. Mechanical characteristics of the braking cylindrical shells of missile ejector under axial compression [J]. Transactions of Beijing Institute of Technology, 2007, 27(2): 99–102. DOI: 10.3969/j.issn.1001-0645.2007.02.002.
[7]	姚保太, 王汉平. 导弹弹射系统中缓冲制动锥的轴向冲击特性 [J]. 固体火箭技术, 2014, 37(6): 863–867. DOI: 10.7673/j.issn.1006-2793.2014.06.023. YAO B T, WANG H P. Mechanical characteristics of the braking cylindrical shells of missile ejector under axial impact [J]. Journal of Solid Rocket Technology, 2014, 37(6): 863–867. DOI: 10.7673/j.issn.1006-2793.2014.06.023.
[8]	陈军葵, 王汉平, 王志军, 等. 导弹弹射系统中缓冲制动锥的结构设计 [J]. 兵器材料科学与工程, 2015, 38(2): 85–90. DOI: 10.3969/j.issn.1004-244X.2015.02.022. CHEN J K, WANG H P, WANG Z J, et al. Structure design of braking cylindrical shells of missile ejector [J]. Ordnance Material Science and Engineering, 2015, 38(2): 85–90. DOI: 10.3969/j.issn.1004-244X.2015.02.022.
[9]	姚如洋, 赵振宇, 尹冠生, 等. 薄壁开孔圆管在轴向荷载作用下的理论研究 [J]. 振动与冲击, 2020, 39(2): 141–147. DOI: 10.13465/j.cnki.jvs.2020.02.020. YAO R Y, ZHAO Z Y, YIN G S, et al. Theoretical analysis on thin-walled holed circular tubes under axial loading [J]. Journal of Vibration and Shock, 2020, 39(2): 141–147. DOI: 10.13465/j.cnki.jvs.2020.02.020.
[10]	王陈凌. 伸缩型高强钢薄壁圆管耐撞性分析及优化设计[D]. 长沙: 湖南大学, 2021: 21–54. DOI: 10.27135/d.cnki.ghudu.2021.003010. WANG C L. Crashworthiness analysis and optimization design of telescopic high-strength steel thin-walled circular tubes [D]. Changsha: Hunan University, 2021: 21–54. DOI: 10.27135/d.cnki.ghudu.2021.003010.
[11]	季銮顺. 可轧制约束下变厚度薄壁结构的参数化建模及耐撞性优化设计 [D]. 镇江: 江苏大学, 2020: 44–83. DOI: 10.27170/d.cnki.gjsuu.2020.001563. JI L S. Parametric modeling and optimal design of crashworthiness for thin-wall structures with variable thickness under rolling constraints [D]. Zhenjiang, Jiangsu: Jiangsu University, 2020: 44–83. DOI: 10.27170/d.cnki.gjsuu.2020.001563.
[12]	刘莉, 高宁, 许喆, 等. 地铁车辆底架薄壁梁吸能结构耐撞性试验与仿真研究 [J]. 铁道科学与工程学报, 2021, 18(7): 1852–1860. DOI: 10.19713/j.cnki.43-1423/u.T20200827. LIU L, GAO N, XU Z, et al. Crashworthiness test and simulation research on the thin-walled beam energy absorption structure of trains [J]. Journal of Railway Science and Engineering, 2021, 18(7): 1852–1860. DOI: 10.19713/j.cnki.43-1423/u.T20200827.
[13]	王春华, 姜红星, 牛慧超, 等. 防冲支架变梯度薄壁构件压溃吸能实验研究 [J]. 机械强度, 2021, 43(5): 1062–1069. DOI: 10.16579/j.issn.1001.9669.2021.05.007. WANG C H, JIANG H X, NIU H C, et al. Research on variable gradient thin-walled energy absorbing component of scour-proof hydraulic support [J]. Journal of Mechanical Strength, 2021, 43(5): 1062–1069. DOI: 10.16579/j.issn.1001.9669.2021.05.007.
[14]	于鹏山, 刘志芳, 李世强. 新型仿竹薄壁圆管的设计与吸能特性分析[J]. 高压物理学报, 2021, 35(5): 054205-1. DOI: 10.11858/gywlxb.20210710. YU P S, LIU Z F, LI S Q. Design and energy absorption characteristic analysis of a new bio-bamboo thin-walled circular tube [J]. Chinese Journal of High Pressure Physics, 2021, 35(5): 054205-1. DOI: 10.11858/gywlxb.20210710.
[15]	JOHNSON G R, COOK W H. A constitutive model and data for metals subjected to large strains, high strain rates and high temperatures [C]// Proceedings of the 7th International Symposium on Ballistics. The Hague, 1983: 541–547.
[16]	项燕飞. 能量吸收材料与结构的评价指标 [D]. 宁波: 宁波大学, 2014: 8–11. XIANG Y F. Key Performance indicators (KPIs) of energy absorption of materials and structures [D]. Ningbo: Ningbo University, 2014: 8–11.
[17]	余同希. 结构的耐撞性和能量吸收装置 [J]. 力学与实践, 1985, 7(3): 2–9. DOI: 10.6052/1000-0879-1985-041.
[18]	庄茁, 张帆, 岑松, 等. ABAQUS非线性有限元分析与实例 [M]. 北京: 科学出版社, 2005: 207–239.

Relative Articles

[1]	CHEN Jie, WANG Kehong, KONG Jian, PENG Yong, LIU Chuang, DONG Kewei, WANG Qipeng, ZHANG Xianfeng. Sub-texture in adiabatic shear bands from arc additively manufactured stainless steel under dynamic loads[J]. Explosion And Shock Waves, 2023, 43(7): 073102. doi: 10.11883/bzycj-2022-0493
[2]	LI Xiaojie, WANG Yuxin, WANG Xiaohong, YAN Honghao, ZENG Xiangyu, WANG Jian. Gas shock waves in the gap between the base and cladding plates during explosive welding[J]. Explosion And Shock Waves, 2021, 41(7): 075301. doi: 10.11883/bzycj-2020-0197
[3]	SHI Tongya, LIU Dongsheng, CHEN Wei, XIE Puchu, WANG Xiaofeng, WANG Yonggang. Dynamic tensile behavior and spall fracture of GP1 stainless steel processed by selective laser melting[J]. Explosion And Shock Waves, 2019, 39(7): 073101. doi: 10.11883/bzycj-2019-0015
[4]	Yang Shiting, Xing Yongming, Zhao Yanru, Hao Yunhong, Li Jijun, Jiang Aifeng. Deformation field in 316L stainless steel by single shot peening[J]. Explosion And Shock Waves, 2017, 37(1): 126-133. doi: 10.11883/1001-1455(2017)01-0126-08
[5]	Sun Wei, Li Xiaojie, Yan Honghao. Underwater explosive welding of tool steel[J]. Explosion And Shock Waves, 2016, 36(1): 107-112. doi: 10.11883/1001-1455(2016)01-0107-06
[6]	Miao Guang-hong, Ma Hong-hao, Shen Zhao-wu, Yu Yong. Double sided explosive cladding of stainless steel and ordinary carbon steel[J]. Explosion And Shock Waves, 2015, 35(4): 536-540. doi: 10.11883/1001-1455(2015)04-0536-05
[7]	Deng Wei, Lu Ming, Tian Xiao-jie. Influence of detonation velocity on interface and combination performances of Al/316L composite tube by explosive welding[J]. Explosion And Shock Waves, 2015, 35(1): 82-88. doi: 10.11883/1001-1455(2015)01-0082-07
[8]	Pan Jian-hua, Chen Xue-dong, Han Yu. Dynamic fracture toughness of S30408 austenitic stainless steel base and weld metals at -196 ℃[J]. Explosion And Shock Waves, 2013, 33(4): 381-386. doi: 10.11883/1001-1455(2013)04-0381-06
[9]	ZHANG Yue-ju, YANG Xu-sheng, LI Xiao-jie, WANG Yong, YAO Zheng, XIAO Hui, ZHAO En-jun. Anexperimentalresearchonexplosiveweldingoftitanium/steelcladplate[J]. Explosion And Shock Waves, 2012, 32(1): 103-107. doi: 10.11883/1001-1455(2012)01-0103-05
[10]	ZHOU Nan, WANG Jin-xiang, WANG Xiao-xu, HANG Yi-fu, QIAN Ji-sheng, RONG Guang. Anti-penetrationperformancesofexplosivelyweldedsteel/aluminium platesimpactedbysphericalprojectiles[J]. Explosion And Shock Waves, 2011, 31(5): 497-503. doi: 10.11883/1001-1455(2011)05-0497-07
[11]	WEI Yan-peng, WU Xian-qian, YU Gang, DUAN Zhu-ping. Constitutiveequationsfordissimilarstainlesssteelslaser-weldedmaterials[J]. Explosion And Shock Waves, 2011, 31(5): 455-462. doi: 10.11883/1001-1455(2011)05-0455-08
[12]	WEI Yan-peng, YU Gang, DUAN Zhu-ping. Mechanicalpropertiesoflaser-weldeddissimilarstainlesssteelsstructure atelevatedtemperatureandhighstrainrates[J]. Explosion And Shock Waves, 2011, 31(5): 504-509. doi: 10.11883/1001-1455(2011)05-0504-06
[13]	YU Lan-ying, LUO Hong, ZENG Xian-guang. Microstructureofthebondinginterfaceinanexplosivelycladded2205 duplexstainlesssteel-16MnRsteelcombination[J]. Explosion And Shock Waves, 2010, 30(4): 445-448. doi: 10.11883/1001-1455(2010)04-0445-04
[14]	SHANG Bing, SHENG Jing, WANG Bao-zhen, HU Shi-sheng. Dynamic mechanical behavior and constitutive model of stainless steel[J]. Explosion And Shock Waves, 2008, 28(6): 527-531. doi: 10.11883/1001-1455(2008)06-0527-05