• ISSN 1001-1455  CN 51-1148/O3
  • EI、Scopus、CA、JST、EBSCO、DOAJ收录
  • 力学类中文核心期刊
  • 中国科技核心期刊、CSCD统计源期刊

全地形车空投冲击损伤分析及寿命评估

闫凯波,  范志伟,  陆思思,  王俊杰,  周鹏

闫凯波, 范志伟, 陆思思, 王俊杰, 周鹏. 全地形车空投冲击损伤分析及寿命评估[J]. 爆炸与冲击. doi: 10.11883/bzycj-2025-0365
引用本文: 闫凯波, 范志伟, 陆思思, 王俊杰, 周鹏. 全地形车空投冲击损伤分析及寿命评估[J]. 爆炸与冲击. doi: 10.11883/bzycj-2025-0365
YAN Kaibo, FAN Zhiwei, LU Sisi, WANG Junjie, ZHOU Peng. Impact damage analysis and life evaluation of all-terrain vehicle airdrop[J]. Explosion And Shock Waves. doi: 10.11883/bzycj-2025-0365
Citation: YAN Kaibo, FAN Zhiwei, LU Sisi, WANG Junjie, ZHOU Peng. Impact damage analysis and life evaluation of all-terrain vehicle airdrop[J]. Explosion And Shock Waves. doi: 10.11883/bzycj-2025-0365

全地形车空投冲击损伤分析及寿命评估

doi: 10.11883/bzycj-2025-0365
基金项目: 国家自然科学基金(52402466);中国博土后科学基金面上项目(2022M723001,2022M713014);重庆市技术创新与应用发展专项重点项目(CSTB2024TIAD-KPX0081);重庆市博土后研究项目(2022CQBSHTB2020);重庆市教育委员会科学技术研究项目(KJZD-K202400704,KJQN202400718);重庆交通大学研究生科创项目(2025S0055)
详细信息
    作者简介:

    闫凯波(1992- ),男,博士,讲师,kaibo_yan@yeah.net.18323817926

    通讯作者:

    陆思思(1993- ),女,博士,副教授,sisi_lu2020@yeah.net

  • 中图分类号: O383

Impact damage analysis and life evaluation of all-terrain vehicle airdrop

  • 摘要: 全地形车的空投过程会对车辆产生强烈冲击,重复空投更易引发车辆累积损伤,进而影响其作业可靠性。结合全地形车各子系统结构特点和力学特性,建立某型全地形车空投系统数值模型,开展全地形车空投冲击载荷传递特性分析,采用低周疲劳分析方法开展空投寿命评估;结合Johnson-Cook损伤模型,研究多着陆场景下车辆的空投冲击损伤演化规律及寿命特性。结果表明:全地形车初始最大损伤位置集中于底盘横梁,随着空投次数增加,最大损伤位置会向立柱等结构转移;理想空投条件下,车辆空投寿命为10次,且寿命随着陆速度增大而降低,其中斜向着陆速度的影响最为显著。值得注意的是,当纵向、斜向、横向、垂向着陆速度分别达到某个阈值时,即全地形车仅空投一次便会发生损坏。相关研究成果为保障多着陆场景下全地形车的重复空投作业能力提供了重要技术支撑。
  • 图  1  全地形车空投着陆系统

    Figure  1.  ATV airdrop landing system

    图  2  不同网格尺寸下最大应变值

    Figure  2.  Maximum strain values under different mesh sizes

    图  3  冲击加速度结果对比

    Figure  3.  Comparison of the impact acceleration between test and simulation

    图  4  空投冲击最大载荷位置

    Figure  4.  Location of Maximum Airdrop Impact Load

    图  5  载荷传递路径

    Figure  5.  Load Transfer Path

    图  6  应变疲劳曲线图

    Figure  6.  The relation between strain and fatigue

    图  7  全地形车空投寿命结果图

    Figure  7.  ATV airdrop lifespan result diagram

    图  8  累积损伤分析流程图

    Figure  8.  Flow chart of cumulative damage analysis

    图  9  空投着陆冲击最大损伤位置分布

    Figure  9.  Distribution of maximum damage location of airdrop landing impact

    图  10  全地形车重复空投损伤演化

    Figure  10.  Damage evolution of repeated airdrop of ATV

    图  11  垂向着陆速度对全地形车空投寿命的影响

    Figure  11.  The influence of vertical landing speed on airdrop lifespan of ATV

    图  12  1 m/s横向速度下空投冲击最大载荷位置

    Figure  12.  Location of maximum airdrop impact load at 1 m/s lateral velocity

    图  13  横向着陆速度下空投冲击载荷传递特性

    Figure  13.  Transmission characteristics of airdrop impact load at lateral landing speed

    图  15  横向着陆速度对全地形车空投寿命的影响

    Figure  15.  The influence of lateral landing speed on airdrop lifespan of ATV

    图  14  不同横向速度下空投着陆冲击最大损伤位置

    Figure  14.  The maximum damage location of airdrop landing impact under different lateral velocities

    图  16  0.2 m/s纵向速度下空投冲击最大载荷位置

    Figure  16.  Maximum load position of airdrop impact at longitudinal velocity 0.2 m/s

    图  17  纵向着陆速度载荷传递路径

    Figure  17.  Transmission characteristics of airdrop impact load at longitudinal landing speed

    图  18  不同纵向速度下空投着陆冲击最大损伤位置

    Figure  18.  The maximum damage location of airdrop landing impact under different longitudinal velocities

    图  19  纵向着陆速度对全地形车空投寿命的影响

    Figure  19.  The influence of longitudinal landing speed on airdrop lifespan of ATV

    图  20  0.3 m/s斜向速度下空投冲击最大载荷位置

    Figure  20.  Maximum load position under airdrop impact at oblique velocity 0.3 m/s

    图  21  斜向速度下空投冲击载荷传递路径

    Figure  21.  Transmission characteristics of airdrop impact load at oblique landing speed

    图  22  不同斜向速度下空投着陆冲击最大损伤位置

    Figure  22.  The maximum damage location of airdrop landing impact under different oblique velocities

    图  23  斜向着陆速度对全地形车空投寿命的影响

    Figure  23.  The influence of oblique landing speed on airdrop life of ATV

    表  1  全地形车各系统实物与有限元模型参照表

    Table  1.   Reference table of physical and finite element models for ATV systems

    底盘/kg
    几何模型有限元模型误差
    146.416147.2960.60%
    车架/kg
    几何模型有限元模型误差
    330.554328.0860.75%
    悬架/kg
    几何模型有限元模型误差
    82.91182.6280.34%
    轮胎/kg
    几何模型有限元模型误差
    22.30022.2310.31%
    其他(动力系统,座椅等/kg)
    几何模型有限元模型误差
    767.819770.9590.41%
    下载: 导出CSV

    表  2  不同着陆速度对全地形车空投的影响

    Table  2.   Effects of different landing velocities on airdrop of ATV

    最大塑性耗散能密度(J/mm3)
    垂向横向纵向斜向
    8.8028.40116.9864.49
    最大应力(MPa)
    垂向横向纵向斜向
    320347451440
    下载: 导出CSV
  • [1] 金晓辉. 军用车辆空投评价指标体系及评价方法 [J]. 军事交通学院学报, 2016, 18(4): 41–43. DOI: 10.16807/j.cnki.12-1372/e.2016.04.0010.

    JIN X H. Evaluation system and evaluating method of military vehicle airdrop [J]. Journal of Military Transportation, 2016, 18(4): 41–43. DOI: 10.16807/j.cnki.12-1372/e.2016.04.0010.
    [2] HOU J, YU G, ZHANG W, et al. Test research on airdrop shock vibration of armored vehicles[C]// Proceedings of 2019 IOP Conference Series: Materials Science and Engineering, Shanghai, China, 2019, 616-012033: 1–6. DOI: 10.1088.1757-899/X.616.1.012033.
    [3] 李正达, 刘琦, 李锦红. 重装空投系统着陆稳定机理研究[C]// 第九届中国航空学会青年科技论坛, 西安, 陕西, 中国, 2020: 241–247. DOI: 10.26914/c.cnkihy.2020.052269.

    LI Z D, LIU Q, LI J H. Research on landing stability of heavy airdrop system [C]// The 9th Youth Science and Technology Forum of the Chinese Society of Aeronautics and Astronautics, Xian, Shaanxi, China, 2020: 241–247. DOI: 10.26914/c.cnkihy.2020.052269.
    [4] YUE J T, TANG L, GUO B H. Simulation analysis of light off-road vehicle’s body frame during airdropping [J]. Advanced Materials Research, 2012, 460: 202–205. DOI: 10.4028/www.scientific.net/AMR.460.202.
    [5] 冯宇. 面向空投着陆冲击过程的装甲车车体动态响应研究 [J]. 现代信息科技, 2019, 3(8): 177–179. DOI: 10.3969/j.issn.2096-4706.2019.08.070.

    FENG Y. Research on dynamic response of armored vehicle body for airdrop landing impact process [J]. Modern Information Technology, 2019, 3(8): 177–179. DOI: 10.3969/j.issn.2096-4706.2019.08.070.
    [6] 冯宇, 于广春, 吴增斌, 等. 某轮式空降战车模拟着地冲击试验方法研究 [J]. 车辆与动力技术, 2019, 154(2): 62–64. DOI: 10.16599/j.cnki.1009-4687.2019.02.012.

    FENG Y, YU G C, WU Z B, et al. Research on the simulated landing impact test method of a wheeled airborne fighting vehicle [J]. Vehicle & Power Technology, 2019, 154(2): 62–64. DOI: 10.16599/j.cnki.1009-4687.2019.02.012.
    [7] 张宇, 王国平, 孙雨田, 等. 基于排气型气囊的多管火箭炮着陆缓冲特性研究 [J]. 南京理工大学学报, 2023, 47(4): 486–493. DOI: 10.14177/j.cnki.32-1397n.2023.47.04.006.

    ZHANG Y, WANG G P, SUN Y T, et al. Research on landing buffer characteristics of multiple rocket launcher based on exhaust air bag [J]. Journal of Nanjing University of Science and Technology, 2023, 47(4): 486–493. DOI: 10.14177/j.cnki.32-1397n.2023.47.04.006.
    [8] 杨旭. 军用越野车车体在空投着陆过程的有限元分析[D]. 沈阳: 东北大学, 2021. DOI: 10.27007/d.cnki.gdbeu.2021.000904.

    YANG X. Finite element analysis of military off-road vehicle body during airdrop landing[D]. Shenyang: Northeastern University, 2021. DOI: 10.27007/d.cnki.gdbeu.2021.000904.
    [9] 曹毅. 冲击下履带车辆动载特性及综合传动结构分析研究[D]. 北京: 北京理工大学, 2016.

    CAO Y. Analysis on dynamic load characteristics and structure of gearbox with impact load[D]. Beijing: Beijing Institute of Technology, 2016.
    [10] 刘涛, 张宏伟, 孙晓旺, 等. 车辆载人空降的试验与仿真研究 [J]. 兵工学报, 2023, 44(08): 2283–2298. DOI: 10.12382/bgxb.2022.0331.

    LIU T, ZHANG H W, SUN X W, et al. Experimental and simulation research on manned airborne of vehicles [J]. Acta Armamentarii, 2023, 44(08): 2283–2298. DOI: 10.12382/bgxb.2022.0331.
    [11] 杨占华, 刘春生, 李军, 等. 空降车辆着陆缓冲过程动态建模仿真 [J]. 兵工学报, 2022, 43(S1): 26–34. DOI: 10.12382/bgxb.2022.A021.

    YANG Z H, LIU C S, LI J, et al. Dynamic modeling and simulation of airborne vehicle’s landing buffer process [J]. Acta Armamentarii, 2022, 43(S1): 26–34. DOI: 10.12382/bgxb.2022.A021.
    [12] 杨彬. 轮胎在空投着陆过程的三维有限元分析[D]. 沈阳: 东北大学, 2019. DOI: 10.27007/d.cnki.gdbeu.2019.002000.

    YANG B. Research on three dimensional finite element analysis of airdrop landing in tire[D]. Shenyang: Northeastern University, 2019. DOI: 10.27007/d.cnki.gdbeu.2019.002000.
    [13] 石坚, 杨占华, 刘春生, 等. 空降车辆着陆缓冲过程仿真分析与模型验证[J]. 车辆与动力技术, 2024, (03): 12–16+42. DOI: 10.16599/j.cnki.1009-4687.2024.03.002.

    SHI J, YANG Z H, LIU C S, et al. Simulation analysis and model verification of airborne vehicle landing buffer[J] Vehicle & Power Technology. 2024, (03): 12–16+42. DOI: 10.16599/j.cnki.1009-4687.2024.03.002.
    [14] ZHOU Y, QIAN Y, ZHANG M, et al. Research on landing damage effects of heavy equipment airdrop vehicles[C]// 10th International Conference on Mechanical Engineering, Materials, and Automation Technology (MMEAT 2024). SPIE, 2024, 13261: 971–977. DOI: 10.1117/12.3046626.
    [15] ZHANG C, ZHAO Y, SHEN Y, et al. The modeling and analysis of vibration response with airdrop vehicle in landing process [J]. Journal of the Brazilian Society of Mechanical Sciences and Engineering, 2024, 46(6): 345–358. DOI: 10.1007/s40430-024-04913-y.
    [16] 付新华, 汪君, 陈勇, 等. 战车载人空投着陆缓冲过程仿真模型研究 [J]. 振动与冲击, 2021, 40(24): 57–64. DOI: 10.13465/j.cnki.jvs.2021.24.008.

    FU X H, WANG J, CHEN Y, et al. A study on soft-landing buffering process of manned armored vehicle airdrop [J]. Journal of Vibration and Shock, 2021, 40(24): 57–64. DOI: 10.13465/j.cnki.jvs.2021.24.008.
    [17] Fu X. Analysis on characteristics of structural impact response of airborne armored vehicle in landing process[C]// Proceedings of 2019 IOP Conference Series: Materials Science and Engineering, Shanghai, China, 2019, 484-012024: 1–8. DOI: 10.1088/1757-899X/484/1/012024.
    [18] Fu X, Lu Y, Wang J, et al. Research on cumulative damage evaluation method for structural impact on airborne armored vehicle in landing process[C]// Proceedings of 2020 IOP Conference Series: Materials Science and Engineering, Jinan, Shandong, China, 2020, 730-012030: 1–9. DOI: 10.1088.1757-899/x.730.1.012030.
    [19] HE J, MA J S, WU D L, et al. Cumulative damage assessment to airdrop vehicle hull for the landing process [J]. WSEA transactions on Applied and Theoretical Mechanics, 2016, 11: 76–84.
    [20] 李建阳, 王红岩, 洪煌杰, 等. 冲击载荷作用下的空降车累积损伤评估方法 [J]. 计算机仿真, 2013, 30(11): 137–142. DOI: 10.3969/j.issn.1006-9348.2013.11.031.

    LI J Y, WANG H Y, HONG H J, et al. Studies on assessment method of cumulative damage for airborne vehicle under Impact [J]. Computer Simulation, 2013, 30(11): 137–142. DOI: 10.3969/j.issn.1006-9348.2013.11.031.
    [21] 李建阳, 王红岩, 芮强, 等. 空降车着陆冲击累积损伤评估方法研究 [J]. 系统仿真学报, 2014, 26(1): 208–214+220. DOI: 10.16182/j.cnki.joss.2014.01.011.

    LI J Y, WANG H Y, RUI Q, et al. Research on cumulative damage assessment method for airborne vehicle at landing based on finite element analysis [J]. Journal of System Simulation, 2014, 26(1): 208–214+220. DOI: 10.16182/j.cnki.joss.2014.01.011.
    [22] 何健, 马吉胜, 刘平, 等. 某空降型自行火炮着陆过程车体损伤评估 [J]. 火力与指挥控制, 2016, 41(06): 129–132+136. DOI: 10.3969/j.issn.1002-0640.2016.06.029.

    HE J, MA J S, LIU P, et al. Damage assessment of hull for landing process of an airdrop self-propelled gun [J]. Fire Control & Command Control, 2016, 41(06): 129–132+136. DOI: 10.3969/j.issn.1002-0640.2016.06.029.
    [23] WANG X, ZHOU Y, ZHANG M. Cumulative damage study of air-dropped aehicles with multiple drops impact[C]// International conference on Advancement in Materials, Manufacturing, and Energy Engineering. Singapore: Springer Nature Singapore, 2022: 289-298. DOI: 10.1007/978-981-99-2375-5_29.
    [24] 王旭东. 某空投特种车辆冲击累积损伤研究[D]. 南京: 南京理工大学, 2023. DOI: 10.27241/d.cnki.gnjgu.2023.001351.

    WANG X D. Research on impact cumulative damage of an air-dropped special vehicle[D]. Nanjing: Nanjing University of Science and Technology, 2023. DOI: 10.27241/d.cnki.gnjgu.2023.001351.
    [25] 倪昀, 陈伟. 基于nCode的前横向稳定杆应变疲劳分析 [J]. 热加工工艺, 2014, 43(02): 52–54+58. DOI: 10.14158/j.cnki.1001-3814.2014.02.069.

    NI Y. CHEN W. Strain fatigue analysis on front transverse stability bar based on ncode [J]. Hot working Technology, 2014, 43(02): 52–54+58. DOI: 10.14158/j.cnki.1001-3814.2014.02.069.
  • 加载中
图(23) / 表(2)
计量
  • 文章访问数:  632
  • HTML全文浏览量:  98
  • PDF下载量:  56
  • 被引次数: 0
出版历程
  • 收稿日期:  2025-11-10
  • 修回日期:  2025-12-21
  • 网络出版日期:  2026-01-21

目录

    /

    返回文章
    返回