Structural optimization design and structural response of elliptical-section penetration projectiles

TAN Yuanshen; HUANG Fenglei; PI Aiguo

doi:10.11883/bzycj-2021-0436

Volume 42 Issue 6

Jun. 2022

Turn off MathJax

Article Contents

Article Navigation > Explosion And Shock Waves > 2022 > 42(6): 063301

TAN Yuanshen, HUANG Fenglei, PI Aiguo. Structural optimization design and structural response of elliptical-section penetration projectiles[J]. Explosion And Shock Waves, 2022, 42(6): 063301. doi: 10.11883/bzycj-2021-0436

Citation:

TAN Yuanshen, HUANG Fenglei, PI Aiguo. Structural optimization design and structural response of elliptical-section penetration projectiles[J]. Explosion And Shock Waves, 2022, 42(6): 063301. doi: 10.11883/bzycj-2021-0436

Citation:

PDF( 3392 KB)

Structural optimization design and structural response of elliptical-section penetration projectiles

doi: 10.11883/bzycj-2021-0436

State Key Laboratory of Explosion Science and Technology, Beijing Institute of Technology, Beijing 100081, China

Received Date: 2021-10-19
Rev Recd Date: 2021-11-11

Available Online: 2022-04-15

Publish Date: 2022-06-24

Abstract

Abstract

According to the engineering application requirements of special-shaped section penetrating projectiles, the structural response and optimal design of elliptical-section penetration projectiles were studied. From this point of view, an improved general design method of elliptical-section projectiles was developed by introducing a dimensionless cartridge thickness coefficient of the elliptical projectile. In order to improve the inertia moment and static moment to the short axis of the cross-section, a bending optimization design method of the elliptical-section projectile was proposed by reducing the cartridge thickness of the projectile to a certain extent and redistributing the reduced materials. Based on a 152-mm-diameter light gas gun test device, the reverse tests of three kinds of elliptical-section hollow projectiles with the long axis of 1.8 cm and the short axis of 1.2 cm penetrating a 2024-O aluminum target were carried out, and the responses of the projectiles in the penetration process were obtained. The projectiles after tests were collected by the soft recovery method, and the deformation of the central axes of the projectile was obtained by the gray processing method. Numerical simulations of the tests were carried out by LS-DYNA. The stress, strain, and penetration load of the projectiles during the penetration process were obtained, and the equivalence of the normal ballistic test and reverse ballistic test was verified. Based on the free-free beam theory, a bending response calculation model of the elliptical-section projectile was established. Through the optimized design, the inertia moment to the short axis of the elliptical section increases by 16.44%, and the static moment increases by 15.95%. Under the test conditions, the bending deflection of the projectile decreases by 25.25%. The structural response model was used to calculate the projectile deformation under the test conditions. The calculation results of the theoretical model are in good agreement with the test results, which shows that the calculation method of the model has a certain accuracy and can provide a reference for engineering design.
- penetration,
- structural response,
- elliptical-section projectile,
- optimization design,
- reverse ballistic

FullText(HTML)

References(16)

References

[1]	DAI X H, WANG K H, LI M R, et al. Rigid elliptical cross-section ogive-nose projectiles penetration into concrete targets [J]. Defence Technology, 2021, 17(3): 800–811. DOI: 10.1016/j.dt.2020.05.011.
[2]	王浩, 潘鑫, 武海军, 等. 椭圆截面截卵形刚性弹体正贯穿加筋板能量耗散分析 [J]. 爆炸与冲击, 2019, 39(10): 103203. DOI: 10.11883/bzycj-2018-0350. WANG H, PAN X, WU H J, et al. Energy dissipation analysis of elliptical truncated oval rigid projectile penetrating stiffened plate [J]. Explosion and Shock Waves, 2019, 39(10): 103203. DOI: 10.11883/bzycj-2018-0350.
[3]	王浩, 武海军, 闫雷, 等. 椭圆横截面弹体斜贯穿双层间隔薄钢板失效模式 [J]. 兵工学报, 2020, 41(S2): 1–11. DOI: 10.3969/j.issn.1000-1093.2020.S2.001. WANG H, WU H J, YAN L, et al. Failure mode of oblique perforation of truncated ogive-nosed projectiles with elliptic cross-section into double-layered thin steel plate with gap space [J]. Acta Armamentarii, 2020, 41(S2): 1–11. DOI: 10.3969/j.issn.1000-1093.2020.S2.001.
[4]	DAI X H, WANG K H, DUAN J, et al. A rigid elliptical cross-sectional projectile with different geometrical characteristics penetration into concrete target [J]. Journal of Physics: Conference Series, 2020, 1507: 032001. DOI: 10.1088/1742-6596/1507/3/032001.
[5]	王文杰, 张先锋, 邓佳杰, 等. 椭圆截面弹体侵彻砂浆靶规律分析 [J]. 爆炸与冲击, 2018, 38(1): 164–173. DOI: 10.11883/bzycj-2017-0020. WANG W J, ZHANG X F, DENG J J, et al. Analysis of projectile penetrating into mortar target with elliptical cross-section [J]. Explosion and Shock Waves, 2018, 38(1): 164–173. DOI: 10.11883/bzycj-2017-0020.
[6]	DONG H, LIU Z H, WU H J, et al. Study on penetration characteristics of high-speed elliptical cross-sectional projectiles into concrete [J]. International Journal of Impact Engineering, 2019, 132: 103311. DOI: 10.1016/j.ijimpeng.2019.05.025.
[7]	刘子豪, 武海军, 高旭东, 等. 椭圆截面弹体侵彻混凝土阻力特性研究 [J]. 北京理工大学学报, 2019, 39(2): 135–141; 146. DOI: 10.15918/j.tbit1001-0645.2019.02.005. LIU Z H, WU H J, GAO X D, et al. Study on the resistance characteristics of elliptical cross-section projectile penetrating concrete [J]. Transactions of Beijing Institute of Technology, 2019, 39(2): 135–141; 146. DOI: 10.15918/j.tbit1001-0645.2019.02.005.
[8]	潘鑫. 椭圆截面刚性弹体贯穿金属靶效能研究 [D]. 北京: 北京理工大学, 2019: 11–13. PAN X. Study on the performance of elliptical cross-sectional rigid projectile perforating metal target [D]. Beijing, China: Beijing Institute of Technology, 2019: 11–13.
[9]	郭磊, 何勇, 潘绪超, 等. 非圆截面弹体侵彻混凝土靶试验与仿真研究 [J]. 兵器材料科学与工程, 2019, 42(3): 62–68. DOI: 10.14024/j.cnki.1004-244x.20190123.002. GUO L, HE Y, PAN X C, et al. Experimental and numerical investigation on the penetration mechanics of non-circular projectile into concrete [J]. Ordnance Material Science and Engineering, 2019, 42(3): 62–68. DOI: 10.14024/j.cnki.1004-244x.20190123.002.
[10]	皮爱国. 大长细比动能弹体结构动态响应研究 [D]. 北京: 北京理工大学, 2007: 18; 93–105.
[11]	刘坚成. 反向撞击下弹体非正侵彻结构响应研究 [D]. 北京: 北京理工大学, 2016: 71–98. LIU J C. Structural response of non-normal penetrating projectile under reverse impact [D]. Beijing, China: Beijing Institute of Technology, 2016: 71–98.
[12]	陈小伟. 动能深侵彻弹的力学设计(I): 侵彻/穿甲理论和弹体壁厚分析 [J]. 爆炸与冲击, 2006, 25(6): 499–505. DOI: 10.11883/1001-1455(2005)06-0499-07. CHEN X W. Mechanics of structural design of EPW (I): the penetration/perforation theory and the analysis on the cartridge of projectile [J]. Explosion and Shock Waves, 2006, 25(6): 499–505. DOI: 10.11883/1001-1455(2005)06-0499-07.
[13]	YU T X, YANG J L, REID S R. Deformable body impact: dynamic plastic behaviour of a moving free-free beam striking the tip of a cantilever beam [J]. International Journal of Solids and Structures, 2001, 38(2): 261–287. DOI: 10.1016/S0020-7683(00)00019-6.
[14]	韩斌, 刘海燕, 水小平. 材料力学教程 [M]. 北京: 电子工业出版社, 2013: 127–169.
[15]	皮爱国, 黄风雷. 大长细比结构弹体侵彻2024-O铝靶的弹塑性动力响应 [J]. 爆炸与冲击, 2008, 28(3): 252–260. DOI: 10.11883/1001-1455(2008)03-0252-09. PI A G, HUANG F L. Elastic-plastic dynamic response of slender projectiles penetrating into 2024-O aluminum targets [J]. Explosion and Shock Waves, 2008, 28(3): 252–260. DOI: 10.11883/1001-1455(2008)03-0252-09.
[16]	LIU J, HUANG F, XU K, et al. Influence of mass ratio on forward and reverse ballistic impact equivalence: experiments, simulations, and mechanism analysis [J]. Experimental Mechanics, 2017, 57(3): 387–404. DOI: 10.1007/s11340-016-0225-3.