Energy absorption characteristics and crashworthiness designs for typical metal aircraft fuselage substructure

ZHANG Xinyue; HUI Xulong; LIU Xiaochuan; BAI Chunyu; LI Xiaocheng; MU Rangke

doi:10.11883/bzycj-2024-0500

Volume 45 Issue 7

Jul. 2025

Turn off MathJax

Article Contents

Article Navigation > Explosion And Shock Waves > 2025 > 45(7): 071001

ZHANG Xinyue, HUI Xulong, LIU Xiaochuan, BAI Chunyu, LI Xiaocheng, MU Rangke. Energy absorption characteristics and crashworthiness designs for typical metal aircraft fuselage substructure[J]. Explosion And Shock Waves, 2025, 45(7): 071001. doi: 10.11883/bzycj-2024-0500

Citation:

ZHANG Xinyue, HUI Xulong, LIU Xiaochuan, BAI Chunyu, LI Xiaocheng, MU Rangke. Energy absorption characteristics and crashworthiness designs for typical metal aircraft fuselage substructure[J]. Explosion And Shock Waves, 2025, 45(7): 071001. doi: 10.11883/bzycj-2024-0500

Citation:

ZHANG Xinyue, HUI Xulong, LIU Xiaochuan, BAI Chunyu, LI Xiaocheng, MU Rangke. Energy absorption characteristics and crashworthiness designs for typical metal aircraft fuselage substructure[J]. Explosion And Shock Waves, 2025, 45(7): 071001. doi: 10.11883/bzycj-2024-0500

PDF( 16407 KB)

Energy absorption characteristics and crashworthiness designs for typical metal aircraft fuselage substructure

doi: 10.11883/bzycj-2024-0500

ZHANG Xinyue^{1, 2, 3
,},
HUI Xulong^{1, 2, 3},
LIU Xiaochuan^{1, 2, 3
,
,},
BAI Chunyu^{1, 2, 3},
LI Xiaocheng^{1, 2, 3},
MU Rangke^{1, 2, 3}

1.
National Key Laboratory of Strength and Structural Integrity, Aircraft Strength Research Institute of China, Xi’an 710065, Shaanxi, China
2.
Key Laboratory of Aviation Science and Technology on Structures Impact Dynamics, Aircraft Strength Research Institute of China, Xi’an 710065, Shaanxi, China
3.
Shaanxi Province Key Laboratory of Aircraft Vibration, Impact and Noise, Xi’an 710065, Shaanxi, China

Received Date: 2024-12-23
Rev Recd Date: 2025-04-22

Available Online: 2025-04-24

Publish Date: 2025-07-01

Abstract

Abstract

To investigate the crashworthiness and energy absorption characteristics of aircraft fuselage substructures and to conduct structural crashworthiness design, this study focuses on a typical metal aircraft fuselage as the research object. A drop test of a typical fuselage substructure was performed, and the energy absorption characteristics were evaluated based on both experimental and simulation analysis results. Subsequently, an energy absorption design for the fuselage substructure was developed. The influence of structural layout parameters on the crash response of the new fuselage substructure was examined through simulation analysis. Comparisons were made regarding structural deformation, impact force-time curves, acceleration responses, and energy absorption for fuselage substructures with different layout parameters. The results indicate that during the crash process of the original structure, the primary energy absorption modes include plastic deformation and fracture in the column, frame, and beam connection areas, bending deformation of cabin floor beams, and failure of connectors. Since all columns bend and break near the connection areas, the other parts of the columns are almost entirely free of plastic deformation, resulting in limited energy absorption by the columns. The new substructure proposed in this study features a novel configuration that fully leverages the advantages of metal plastic deformation. Compared to the original configuration, the new substructure exhibits more uniform deformation while maintaining the same total mass of the fuselage structure. It significantly reduces the peak load and acceleration at the early stage of the crash. The proportion of energy absorption by the frame and energy-absorbing components has increased markedly. After optimization, the average overload of the new fuselage substructure is reduced by 30.8% compared to the original configuration. The average acceleration of the two mass points on the cabin floor of the new fuselage substructure is reduced by 25.0% and 37.6%, respectively, compared to the original configuration. These findings provide valuable insights and references for the crashworthiness design of aircraft fuselage substructures.
- fuselage substructure,
- crashworthiness,
- drop test,
- energy absorption characteristics,
- crashworthy design

FullText(HTML)

References(33)

References

[1]	刘小川, 郭军, 孙侠生, 等. 民机机身段和舱内设施坠撞试验及结构适坠性评估 [J]. 航空学报, 2013, 34(9): 2130–2140. DOI: 10.7527/S1000-6893.2013.0182. LIU X C, GUO J, SUN X S, et al. Drop test and structure crashworthiness evaluation of civil airplane fuselage section with cabin interiors [J]. Acta Aeronautica et Astronautica Sinica, 2013, 34(9): 2130–2140. DOI: 10.7527/S1000-6893.2013.0182.
[2]	刘小川, 白春玉, 惠旭龙, 等. 民机机身结构耐撞性研究的进展与挑战 [J]. 固体力学学报, 2020, 41(4): 293–323. DOI: 10.19636/j.cnki.cjsm42-1250/o3.2020.035. LIU X C, BAI C Y, XI X L, et al. Progress and challenge of research on crashworthiness of civil airplane fuselage structures [J]. Chinese Journal of Solid Mechanics, 2020, 41(4): 293–323. DOI: 10.19636/j.cnki.cjsm42-1250/o3.2020.035.
[3]	中国民用航空局. 中国民用航空规章: 第25部运输类飞机适航标准 CCAR-25-R4 [S]. 北京: 中国民用航空局, 2011. Civil Aviation Administration of China. China civil aviation regulations: part 25-transport aircraft airworthiness standards CCAR-25-R4 [S]. Beijing: CAAC, 2011.
[4]	LIU X C, GUO J, BAI C Y, et al. Drop test and crash simulation of a civil airplane fuselage section [J]. Chinese Journal of Aeronautics, 2015, 28(2): 447–456. DOI: 10.1016/j.cja.2015.01.007.
[5]	张欣玥, 惠旭龙, 刘小川, 等. 典型金属民机机身结构坠撞特性试验 [J]. 航空学报, 2022, 43(6): 526234. DOI: 10.7527/S1000-6893.2022.26234. ZHANG X Y, XI X L, LIU X C, et al. Experimental study on crash characteristics of typical metal civil aircraft fuselage structure [J]. Acta Aeronautica et Astronautica Sinica, 2022, 43(6): 526234. DOI: 10.7527/S1000-6893.2022.26234.
[6]	刘小川, 惠旭龙, 张欣玥, 等. 典型民用飞机全机坠撞实验研究 [J]. 航空学报, 2024, 45(5): 529664. DOI: 10.7527/S1000-6893.2023.29664. LIU X C, XI X L, ZHANG X Y, et al. Full-scale crash experimental study of typical civil aircraft [J]. Acta Aeronautica et Astronautica Sinica, 2024, 45(5): 529664. DOI: 10.7527/S1000-6893.2023.29664.
[7]	冯振宇, 程坤, 赵一帆, 等. 运输类飞机典型货舱地板下部结构冲击吸能特性 [J]. 航空学报, 2019, 40(9): 222907. DOI: 10.7527/S1000-6893.2019.22907. FENG Z Y, CHENG K, ZHAO Y F, et al. Energy-absorbing characteristics of a typical sub-cargo fuselage section of a transport category aircraft [J]. Acta Aeronautica et Astronautica Sinica, 2019, 40(9): 222907. DOI: 10.7527/S1000-6893.2019.22907.
[8]	牟浩蕾, 谢威威, 解江, 等. 坠撞环境下乘员伤害分析及飞机适坠性评估 [J]. 航空学报, 2024, 45(3): 228786. DOI: 10.7527/S1000-6893.2023.28786. MOU H L, XIE W W, XIE J, et al. Occupant injury analysis and aircraft crashworthiness evaluation under crash scenarios [J]. Acta Aeronautica et Astronautica Sinica, 2024, 45(3): 228786. DOI: 10.7527/S1000-6893.2023.28786.
[9]	彭亮. 基于乘员生存性的机身结构适坠性设计与评价方法研究 [D]. 西安: 西北工业大学, 2018. DOI: 10.27406/d.cnki.gxbgu.2018.000284. PENG L. Research on design and evaluation method of airframe structural crashworthiness based on occupants survivability [D]. Xi’an: Northwestern Polytechnical University, 2018. DOI: 10.27406/d.cnki.gxbgu.2018.000284.
[10]	DEEPAK S. Crashworthy design and analysis of aircraft structures [D]. Philadelphia: Drexel University, 2013.
[11]	JACKSON K E. Finite element simulations of two vertical drop tests of F-28 fuselage sections [M]. Virginia: National Aeronautics and Space Administration, 2018.
[12]	FASANELLA E L, JACKSON K E. Crash simulation of a vertical drop test of a B737 fuselage section with auxiliary fuel tank: 23681-0001 [R]. Hampton: US Army Research Laboratory, Vehicle Technology Directorate, NASA Langley Research Center, 2002.
[13]	JACKSON K E, FASANELLA E L. Crash simulation of vertical drop tests of two Boeing 737 fuselage sections [R]. Washington: Office of Aviation Research, 2002.
[14]	冯振宇, 张晓敏, 牟浩蕾, 等. 不同冲击条件对机身结构适坠性的影响 [J]. 机械科学与技术, 2013, 32(3): 353–357. DOI: 10.13433/j.cnki.1003-8728.2013.03.023. FENG Z Y, ZHANG X M, MOU H L, et al. Influences of different impact conditions on aircraft fuselage crashworthiness [J]. Mechanical Science and Technology for Aerospace Engineering, 2013, 32(3): 353–357. DOI: 10.13433/j.cnki.1003-8728.2013.03.023.
[15]	邹田春, 牟浩蕾, 任健, 等. 滚转角度对民机机身结构耐撞性能的影响 [J]. 机械强度, 2014, 36(1): 139–143. DOI: 10.16579/j.issn.1001.9669.2014.01.022. ZOU T C, MOU H L, REN J, et al. Effects of roll angles on civil aircraft fuselage crashworthiness [J]. Journal of Mechanical Strength, 2014, 36(1): 139–143. DOI: 10.16579/j.issn.1001.9669.2014.01.022.
[16]	RICCIO A, RAIMONDO A, DI CAPRIO F, et al. Experimental and numerical investigation on the crashworthiness of a composite fuselage sub-floor support system [J]. Composites Part B: Engineering, 2018, 150: 93–103. DOI: 10.1016/j.compositesb.2018.05.044.
[17]	RICCIO A, SAPUTO S, SELLITTO A, et al. On the crashworthiness behaviour of a composite fuselage sub-floor component [J]. Composite Structures, 2020, 234: 111662. DOI: 10.1016/j.compstruct.2019.111662.
[18]	PAZ J, DÍAZ J, ROMERA L, et al. Optimisation of thin-walled hybrid vertical struts for crashworthy aircraft designs [J]. Structural and Multidisciplinary Optimization, 2020, 61(1): 141–158. DOI: 10.1007/s00158-019-02350-3.
[19]	FERABOLI P. Development of a corrugated test specimen for composite materials energy absorption [J]. Journal of Composite Materials, 2008, 42(3): 229–256. DOI: 10.1177/0021998307086202.
[20]	SCHATROW P, WAIMER M. Crash concept for composite transport aircraft using mainly tensile and compressive absorption mechanisms [J]. CEAS Aeronautical Journal, 2016, 7(3): 471–482. DOI: 10.1007/s13272-016-0203-6.
[21]	WAIMER M, KOHLGRÜBER D, KECK R, et al. Contribution to an improved crash design for a composite transport aircraft fuselage: development of a kinematics model and an experimental component test setup [J]. CEAS Aeronautical Journal, 2013, 4(3): 265–275. DOI: 10.1007/s13272-013-0070-3.
[22]	WAIMER M, KOHLGRÜBER D, HACHENBERG D, et al. Experimental study of CFRP components subjected to dynamic crash loads [J]. Composite Structures, 2013, 105: 288–299. DOI: 10.1016/j.compstruct.2013.05.030.
[23]	DELSART D, PORTEMONT G, WAIMER M. Crash testing of a CFRP commercial aircraft sub-cargo fuselage section [J]. Procedia Structural Integrity, 2016, 2: 2198–2205. DOI: 10.1016/j.prostr.2016.06.275.
[24]	HEIMBS S, STROBL F, MIDDENDORF P, et al. Composite crash absorber for aircraft fuselage applications [J]. WIT Transactions on the Built Environment, 2010, 113(12): 3–14. DOI: 10.2495/SU100011.
[25]	REN Y R, XIANG J W, MENG S H, et al. Crashworthiness of civil aircraft subject to soft soil and concrete impact surface [J]. Procedia Engineering, 2014, 80: 193–201. DOI: 10.1016/j.proeng.2014.09.074.
[26]	JIANG H Y, REN Y R, GAO B H, et al. Design of novel plug-type triggers for composite square tubes: enhancement of energy-absorption capacity and inducing failure mechanisms [J]. International Journal of Mechanical Sciences, 2017, 131/132: 113–136. DOI: 10.1016/j.ijmecsci.2017.06.050.
[27]	谭丽辉, 徐涛, 崔晓梅, 等. 带有圆弧形凹槽金属薄壁圆管抗撞性优化设计 [J]. 爆炸与冲击, 2014, 34(5): 547–553. DOI: 10.11883/1001-1455(2014)05-0547-07. TAN L H, XU T, CUI X M, et al. Design optimization for crashworthiness of metal thin-walled cylinders with circular arc indentations [J]. Explosion and Shock Waves, 2014, 34(5): 547–553. DOI: 10.11883/1001-1455(2014)05-0547-07.
[28]	张欣玥, 惠旭龙, 葛宇静, 等. 中低速压缩加载下不同截面构型复合材料薄壁结构吸能特性及失效分析 [J]. 爆炸与冲击, 2022, 42(6): 063102. DOI: 10.11883/bzycj-2021-0347. ZHANG X Y, XI X L, GE Y J, et al. Energy absorption characteristics and failure analysis of composite thin-walled structures with different cross-sectional configurations under medium- and low-speed compression loading [J]. Explosion and Shock Waves, 2022, 42(6): 063102. DOI: 10.11883/bzycj-2021-0347.
[29]	JIANG H Y, REN Y R, GAO B H. Research on the progressive damage model and trigger geometry of composite waved beam to improve crashworthiness [J]. Thin-Walled Structures, 2017, 119: 531–543. DOI: 10.1016/j.tws.2017.07.004.
[30]	汪洋, 吴志斌, 刘富. 复合材料货舱地板立柱压溃响应试验 [J]. 复合材料学报, 2020, 37(9): 2200–2206. DOI: 10.13801/j.cnki.fhclxb.20200111.001. WANG Y, WU Z B, LIU F. Crush experiment of composite cargo floor stanchions [J]. Acta Materiae Compositae Sinica, 2020, 37(9): 2200–2206. DOI: 10.13801/j.cnki.fhclxb.20200111.001.
[31]	REN Y R, XIANG J W. Improvement of aircraft crashworthy performance using inversion failure strut system [J]. Aircraft Engineering and Aerospace Technology, 2017, 89(2): 330–337. DOI: 10.1108/AEAT-09-2015-0205.
[32]	REN Y R, ZHANG H Y, XIANG J W. A novel aircraft energy absorption strut system with corrugated composite plate to improve crashworthiness [J]. International Journal of Crashworthiness, 2018, 23(1): 1–10. DOI: 10.1080/13588265.2017.1301082.
[33]	《飞机设计手册》总编委会. 飞机设计手册第3册材料 [M]. 北京: 航空工业出版社, 1997: 186–260. General Editorial Board of Aircraft Design Manual. Aircraft design manual volume 3: materials [M]. Beijing: Aviation Industry Press, 1997: 186–260.